Dad shares money-saving toilet-fix hack to try instead of calling a plumber: 'Anyone can do this'

A running toilet is more than just an annoyance; it can lead to significant water wastage and increased utility bills. Modern toilets typically use about 1.2 gallons per flush, and a constantly running toilet can waste between 30 to 50 gallons of water daily. There are two primary reasons for a toilet to run continuously: a faulty fill valve or a leaky flapper. Both issues are common and can be addressed without professional help, saving homeowners considerable costs compared to hiring a plumber, who might charge $150 or more per hour. This article provides a step-by-step guide to diagnose and fix these problems, with necessary parts costing less than $50. The first common problem is a faulty flapper. The flapper is a rubber gasket at the bottom of the toilet tank that controls the release of water into the bowl. Over time, it can degrade, allowing water to trickle out and causing the tank to refill intermittently, often referred to as “ghost flushing.” Mineral buildup from hard water or natural aging can make the rubber less pliable and misshapen. To diagnose this, one can remove the tank lid and press down on the flapper; if the running stops, replacing the flapper is the solution. Before starting, it is crucial to gather a bucket, old towels, and take photos of the existing setup, including the flapper chain's length. The water supply to the toilet should be shut off, and the tank drained by flushing. After soaking up any remaining water, the old flapper can be removed, and a new one installed according to its instructions. Proper seating of the flapper and correct chain length are essential for its functionality. Finally, the water supply is restored, and the toilet is flushed to test the repair. The second common issue is a bad fill valve, which causes the toilet to run continuously as the tank constantly attempts to fill. The fill valve is the tall component with a float inside the tank. Similar to replacing the flapper, taking photos of the setup and purchasing the correct replacement kit are important. After shutting off the water supply and draining the tank, the fill valve is removed by unscrewing the water supply line and the locknut at the bottom of the tank. A bucket and towels should be in place to catch any spills. The new fill valve is then inserted and secured, ensuring it is not overtightened to avoid damage. The height of the new valve should be adjusted to match the original setting, especially for taller tanks. A refill tube connects the fill valve to the overflow pipe and may need trimming to the correct length. Once installed, the water is turned back on to check for leaks as the tank partially fills, and a final flush tests the complete repair. Repairing a running toilet is generally straightforward, requiring attention to detail and the correct replacement parts. Homeowners are encouraged not to be intimidated by the task, to allow ample time, take reference photos, and always ensure the water supply is turned off before beginning any work. Essential tools for this repair include channel lock pliers, and replacement flappers and fill valves are readily available. Successfully performing these repairs can significantly reduce water waste and save money on plumbing services. #HomeMaintenance #PlumbingRepair #DIYHomeRepair #RunningToilet #WaterConservation #FlapperReplacement #FillValveReplacement #BathroomMaintenance

This article outlines 14 common toilet problems that homeowners frequently encounter, along with their causes and solutions. It emphasizes that while many issues can be fixed with basic tools, ignoring them can lead to more significant damage and costly repairs. The article begins by explaining the fundamental mechanics of a toilet, detailing how flushing works from the flapper opening to the tank refilling, to help readers better understand the underlying causes of malfunctions. The first problem discussed is a running toilet, often caused by a faulty flapper or fill valve. Solutions include replacing a worn flapper, adjusting the float arm, or replacing the fill valve itself. Next, a rocking toilet is addressed, which can be due to loose bolts, an uneven floor, or a damaged wax seal. The article advises tightening bolts, using shims for uneven floors, and checking/replacing the wax ring if leaks are suspected. For slamming toilet lids, a simple fix involves adding a vinyl bumper to the tank lid or installing a slow-close toilet seat. Cracked toilet seats are common, and while replacing them is easy, removing corroded bolts can be challenging. The article suggests drilling through rusted bolts if lubricants fail. Condensation on the toilet tank, known as a "sweaty toilet," is explained as a humidity issue that can cause floor damage. Insulated tanks are mentioned as a preventive measure. A bubbling toilet or fluctuating water levels often indicate a clogged or improperly vented drain line. While simple clogs can be snaked, persistent bubbling usually points to a more complex venting problem requiring professional help. Poor flushing performance, especially in master baths, might be due to an overlooked temporary plug in the roof's vent pipe. Removing this plug can restore proper function; otherwise, a defective toilet or drain line obstruction may be the cause. A sluggish toilet often signals mineral buildup in the rim's rinse holes, which can be cleared with a coat hanger. Clogged toilets are best tackled with a plunger, specifically one with an extension flange for better suction. For stubborn clogs, a drain snake might be necessary. The importance of caulking the toilet to the floor is highlighted to prevent odors and moisture from accumulating underneath. Loose toilet seats can be fixed with rubber bushings and seat stabilizers. Finally, corroded flush handles, which can cause constant running, require replacement, with a specific note about the reverse thread of the retaining nut. Rusty toilet seat hinges, a cosmetic issue, can be remedied by dabbing clear nail polish on the screw heads or filling holes with caulk if already rusted. #ToiletMaintenance #PlumbingProblems #DIYHomeRepair #BathroomFixes #RunningToilet #CloggedToilet #ToiletFlushing #HomeMaintenance #PlumbingTips

Updating bathroom hardware, including cabinet knobs, drawer pulls, towel bars, and toilet paper holders, is a simple, cost-effective, and impactful way to refresh a bathroom's aesthetic. Interior designers emphasize that these small details can significantly alter the overall feel of a space without requiring extensive renovation. Anna Filippova of Hyphen & Co. notes that new hardware introduces a fresh element and is easy to install. Carneil Griffin of Griffin Direction Interiors highlights that hardware is both decorative and functional, allowing for the introduction of personality and drawing attention to key areas like vanities or unique tile work. This minor change provides a mini facelift, is typically quick to implement, and can be remarkably inexpensive, with items like solid stone and marble cabinet knobs available for around $7 each, offering a budget-friendly alternative to more costly upgrades such as new tiling or painting. The article provides four designer-approved ideas for selecting bathroom hardware that makes a significant impression. The first recommendation is to swap out vanity cabinet hardware. Interior designer Robin Baron suggests choosing bold colors or shapes to make a statement, likening hardware to jewelry for the vanity. For a more subtle refresh, Marie Flanigan advises selecting knobs and pulls in a slightly different finish, such as transitioning from silver to gold, which can enhance existing materials and color schemes. An example provided is a bathroom designed by Flanigan where gold pulls effectively complement a stained wood vanity. The advice encourages experimentation with different pulls to find the perfect match for the bathroom's color scheme. The second suggestion is to upgrade the towel bar and consider adding a towel ring. Caroline Slason, associate designer at Megan Hopp Design, explains that a well-designed towel bar not only serves a daily function but also elevates the appearance of the towels themselves. She favors towel bars with sophisticated finishes and clean lines. For instance, in an all-white bathroom, a white towel bar can create an unexpected, chic look that highlights monogrammed towels. Adding a towel ring, or updating an existing one, can further enhance the area around the bathroom sink. Towel rings come in various shapes, styles, and finishes, acting as functional wall decor, and their installation requires only basic tools. Thirdly, the article emphasizes the importance of the toilet paper holder. Carneil Griffin points out that despite their utility, toilet paper holders are often overlooked visually. Swapping a standard holder for a more sophisticated version can improve the bathroom's ambiance. Whether opting for a sleek wall-mounted design or an attractive standing holder, a stylish toilet paper holder can add a unique touch or help unify the overall design. Finally, for a hardware upgrade that also improves daily living, Griffin suggests considering a nicer showerhead. He highlights that creating a spa-like bathroom contributes to mental well-being, and luxurious jet spray or rainfall-style showerheads are readily available and affordable, starting from as little as $20. A crucial tip is to ensure that all new hardware and fixture finishes coordinate, unless a deliberate mixed-metals look is desired. #BathroomUpdate #HomeDecor #InteriorDesign #DIYHomeImprovements #BudgetDecor #HardwareUpgrade #BathroomHardware #DesignTips

The article details the various factors influencing the cost of replacing a toilet flange, a crucial component connecting the toilet bowl to a home's drainage system and securely affixing it to the floor. A wax ring is placed on the flange to create an airtight seal, preventing leaks, odors, and gases. The average cost for parts and labor to replace a toilet flange typically ranges from $145 to $165, with the job usually taking only a few hours. This cost can fluctuate based on the flange material, labor rates, and the need for additional repairs. One significant cost factor is the toilet flange material. While most flanges are inexpensive, ranging from $5 to $30, specialized materials like brass can cost up to $75. Common types include PVC (Polyvinyl Chloride), which is affordable and durable, often costing $5 to $20. Stainless steel flanges, priced between $5 and $30, offer corrosion resistance and a longer lifespan. Copper flanges, at around $35, have antibacterial properties. Cast iron flanges, costing $25 to $40, are very sturdy and can last for decades, though they are susceptible to rust if not maintained. Brass flanges, while the most expensive at up to $75, are highly durable and heat-resistant. Labor costs also significantly impact the total expense. Plumbers typically charge $45 to $150 per hour for this job. Since replacing a toilet flange is usually a quick task, taking only a couple of hours, the labor component is relatively contained. A professional plumber will also assess the area for further damage caused by leaks, such as to the surrounding floor or a cracked drainpipe, adding value beyond just the replacement. Project complexity can increase costs. While a straightforward replacement involves simply lifting the toilet, removing the old flange, and installing a new one with a fresh wax ring, complications can arise. Prolonged leaks might lead to damage to the subfloor or flooring, necessitating additional repairs. The cost to replace a subfloor can range from $173 to $300, and replacing floor covering can cost between $200 and $800, though these costs might be lower for small bathroom areas. Repairing a cracked or rusted drainpipe, which might require accessing pipes from a lower floor or basement, can average around $696, depending on the extent of the damage and accessibility. Homeowners should consider replacing a toilet flange if they observe visible leaks around the toilet base, persistent sewer odors, loose tiles around the toilet, or an unstable/wobbly toilet. These signs indicate a potential issue with the flange or its seal. While DIY replacement is possible and can save money on labor, it requires plumbing expertise, as improper installation can lead to future leaks and damage. Many experts recommend hiring a professional plumber for a thorough inspection and proper installation, ensuring peace of mind and preventing more costly repairs in the long run. Tips for saving money on toilet flange replacement include selecting cheaper materials like PVC or stainless steel, only replacing the wax ring if the flange is in good condition, purchasing fixtures yourself when on sale, and combining plumbing jobs if other issues need attention. Before hiring a plumber, it is advisable to ask about their licensing and insurance, recommended materials, estimated costs and duration, hourly rates, and warranty information. #ToiletFlange #Plumbing #HomeMaintenance #BathroomRepair #PlumberCost #DIYPlumbing #HomeImprovement #LeakDetection #SewerOdor

Emily Rodgers, a homeowner from Dayton, Ohio, successfully renovated her outdated and dull bathroom on a limited budget, showcasing a do-it-yourself approach to home improvement. Having recently completed a kitchen renovation, Rodgers sought cost-effective solutions for her bathroom. Her initial plan involved painting existing linoleum floor tiles with a stencil, but she discovered marble look-alike peel-and-stick tiles at a home improvement store. She was impressed by the quality of these tiles, noting their matte finish and irregular marble veining. The installation process was straightforward, with the most challenging aspect being cutting around the toilet. Rodgers mentioned the possibility of using grout between the tiles for a more realistic appearance and plans to keep them for a while, depending on their durability. For the walls, Rodgers replaced the old square subway tiles with shiplap. She had previous experience with shiplap from her kitchen renovation and appreciated its affordability and ease of use. The choice of a green paint color for the walls helped unify the new design elements. Other significant updates included removing the old vanity and installing a new one, adding a new pendant light fixture, and hanging a new mirror. Most of the project, including the demolition, shiplap installation, painting, and floor installation, was completed over a single weekend. The sourcing of the mirror and light fixture extended the overall timeline by a couple of weeks. The entire renovation, encompassing all materials and fixtures, cost approximately $500, with the new vanity accounting for a substantial portion of this expense. Rodgers emphasized the personal satisfaction derived from undertaking these renovations herself, stating that she handles all her home makeovers and feels immense pride in each project. Her work and other projects are documented on her Instagram account, @mylushabode. #BathroomMakeover #DIYHomeRenovation #PeelAndStickTiles #Shiplap #BudgetDecorating #HomeImprovement #InteriorDesign #HomeDecor

This article reviews various toilet plungers and related tools, offering recommendations for different needs and preferences. The primary recommendation is the Korky 99-4A Max Performance Plunger due to its superior clog-clearing power, attributed to its unique beehive design and pliable rubber that conforms to irregular bowl shapes. The plunger's T-handle grip also enhances user comfort and efficiency during plunging. For users seeking a compatible drip tray, the MAXClean Universal Plunger Holder Drip Tray is suggested as it securely holds the Korky plunger and contains drips, offering an easy-to-clean, one-piece design. While Korky offers a version with a drip tray, it was found to be less functional due to a tight fit. For those prioritizing aesthetics over raw power, the Simplehuman Toilet Plunger is presented as a runner-up. It features an attractive design with a stainless steel shaft and a stylish caddy that conceals the plunger cup, allows for air circulation for drying, and has a magnetic attachment for easy, drip-free transport. However, it demonstrated less power in testing compared to the Korky 99-4A. For severe clogs that traditional plungers cannot resolve, the Ridgid 59787 K-3 Toilet Auger is recommended. This professional-grade tool, also known as a closet auger, uses a coiled metal snake to physically dislodge obstructions. The Ridgid model is praised for its robust build quality, ergonomic handles, and secure clip for storage, making it a reliable solution for persistent blockages, despite its larger size and more complex cleaning requirements. The article also provides practical advice on how to properly use a plunger, emphasizing the importance of filling the plunger cup with water to create an effective seal and employing gentle, repeated back-and-forth motions. Instructions for cleaning a plunger are included, suggesting methods like using bleach or oxygen bleach for disinfection, with a preference for oxygen bleach in homes with septic systems. In addition to the top recommendations, the article reviews several competing products, explaining why they did not meet the selection criteria. Issues cited include stiff plungers that were difficult to use, poorly designed drip trays that were hard to clean, flimsy handles, and unconventional designs that were either ineffective, messy, or impractical for home use. The review process involved speaking with plumbing and cleaning experts, personal experience, and controlled testing on various toilet types, including a custom-built test rig with clear pipes to observe clog movement directly. #ToiletPlunger #HomeMaintenance #PlumbingTools #ClogRemoval #ProductReview #HouseholdEssentials #BathroomFixtures #DIYHome

The article details the personal experience of Erica Chayes Wida, who, along with her husband, undertook a bathroom renovation project during the initial phase of the coronavirus pandemic. Faced with stay-at-home orders and two young children, the family decided to transform their outdated, 1960s-era pink bathroom. What initially seemed like a poorly timed and daunting task evolved into a source of solace and a family bonding experience. The renovation process was divided into several key steps. The first involved creating a comprehensive 'vision board.' Instead of haphazardly selecting items online, the author utilized platforms like Pinterest, Instagram, and home decor websites to compile a digital collection of inspiring 'look-and-feel' photos and specific product images. This visual guide helped in balancing design elements such as creamy painted walls, textured wood accents, a black and white marble vanity, honeycomb black tiles, and a red-hued rug, providing a structured approach to the design without professional assistance. The second tip focused on selecting items for purchase. While the author opted for a complete gut renovation, the article emphasizes that budget-friendly updates are also achievable. Ariel Kaye, founder of Parachute and author of 'How to Make a House a Home,' suggests painting with cool, calming colors like cream, white, pale green, or sea blue for a spa-like atmosphere. Kaye also recommends swapping out old hardware, such as faucets, cabinet pulls, and lighting, to significantly refresh a smaller space. The author applied this advice by choosing oil-rubbed bronze hardware from Wayfair's Koehler collection for a cohesive black-and-white aesthetic and an affordable white Minnetrista Double Bathroom Vanity Set by Andover Mills, customizing it with matte black knobs. Modern black vanity lights with yellow-hued Edison bulbs were chosen to create a warm glow, complemented by Langston Hexagon Porcelain Field Tiles for the floor. Third, the article stresses the importance of thorough preparation before commencing any construction work. For DIY enthusiasts, it is crucial to research how-to guides and understand basic construction principles. Key considerations include inspecting for and repairing any hidden damage, such as rot or water damage, especially in older bathrooms, to ensure structural stability. Adhering to current standard energy codes for lights, faucets, and toilets is also highlighted to reduce utility bills and enhance resale value. The author advises caution regarding the scope of DIY work, recommending that electrical and plumbing tasks be left to qualified professionals to prevent safety hazards like fires or catastrophic leaks. Finally, the article advocates for adding personal touches to make the renovated space truly unique and reflective of one's personality. Ariel Kaye suggests incorporating natural elements like plants for ambiance and using scents, such as eucalyptus in the shower, for relaxation. The author transformed her black-and-white bathroom by introducing bohemian elements through natural wood shelving, an orange patterned rug, and colorful flowers, creating a personal oasis for self-reflection. The article concludes by encouraging readers to enjoy the fruits of their labor in their newly renovated, personalized bathroom space. #BathroomRenovation #DIYHomeImprovement #HomeDesign #PandemicProject #InteriorDecor #SelfCareSpace #BudgetFriendlyRenovation

This blog section provides a comprehensive guide to various aspects of bathroom design, maintenance, and repair, catering to both aesthetic preferences and functional needs. It addresses common issues and offers practical DIY solutions, alongside expert recommendations for product selection and upgrade considerations. Key topics covered include methods for unclogging toilets, ranging from traditional plungers to household remedies like dish soap, baking soda, and vinegar, as well as unconventional tools such as wire hangers. The section also features advice on choosing the best toilet plungers, distinguishing between one-piece and two-piece toilets, and understanding the benefits and installation of touchless bathroom faucets. For those looking to enhance their bathroom's appearance, the content offers inspiration for shower tile designs that can transform the space with color, texture, and pattern. It also critically examines popular bathroom upgrades, identifying those that may not offer long-term value and suggesting more worthwhile alternatives. Practical repair guides are provided for essential bathroom components, such as replacing a toilet fill valve in a few simple steps to save water and money. It also educates readers on items that should not be flushed down the toilet to prevent costly plumbing issues and explains the functional purpose of the 'dobby border' on bath towels. Maintenance tips are plentiful, including effective cleaning hacks, such as using a used dryer sheet to clean toilets and surprising methods to make general bathroom cleaning a breeze. The importance of a clean bathroom exhaust fan is highlighted, with a hack to test airflow and a step-by-step guide on removing mold from bathroom ceilings to prevent recurrence. Further articles delve into detailed considerations for larger bathroom elements, such as the cost, dimensions, types, and installation of clawfoot tubs, and what to know before purchasing freestanding tubs. It also addresses potential fire hazards associated with bathroom exhaust fans and provides guidance on how to prevent them. For remodeling projects, there are articles on installing bathroom grab bars for added safety and convenience, and tips for choosing the most suitable bathroom countertops. Detailed shower tile layout advice is offered for planning, measuring, and installing tiles during a bathroom renovation. Troubleshooting guides cover common problems like a toilet that won't flush, outlining the most likely reasons and how to fix them. Instructions for properly removing a toilet are also included. Innovative solutions such as using inline exhaust fans to vent multiple bathrooms from a single attic fan are discussed. Finally, the section covers removing a stopper from a bathroom sink and offers solutions for various types of stoppers. It also showcases inspirational makeovers, such as Joanna Gaines' castle bathroom and laundry room renovation, and provides practical advice on removing rust stains from bathroom surfaces, which are often caused by iron in the water supply. Water dripping from a bathroom fan is also addressed, attributing it to condensation or roof leaks and offering solutions. The section concludes with creative shower niche ideas for convenient storage and a guide on replacing noisy bathroom exhaust fans. #BathroomDesign #HomeRepair #Plumbing #ToiletMaintenance #ShowerTiles #HomeImprovement #BathroomCleaning #DIYProjects #BathroomFixtures

This article details a budget-friendly bathroom renovation undertaken by writer and editor Alexis Teasdale, who transformed her outdated bathroom for just $550. Faced with the challenge of renovating with three young children, Teasdale opted for a less invasive and more cost-effective approach than a full gut renovation. Her goal was to brighten the bathroom, which previously featured a dark 90s style blended with country-cottage elements, and make it more appealing for guests. The key to this transformation was the use of self-stick vinyl floor tiles, which she discovered online and sourced locally from Bunnings after finding international shipping costs prohibitive for similar products. The renovation primarily focused on cosmetic changes that significantly altered the room's aesthetic. The process began with a thorough cleaning of the existing bathroom surfaces using sugar soap and mould remover, followed by rinsing and drying. Teasdale then meticulously taped off the edges and applied three coats of Dulux paint in 'Snow Season' to the walls and existing tiles, using a roller brush for an even finish. During this painting phase, fixtures such as the bathroom mirror cabinet, towel rails, and toilet roll holder were removed to facilitate a neater application. After the paint dried completely, the self-stick vinyl tiles were laid on the floor. Teasdale, who had no prior experience with vinyl tile installation or tile painting, found the process to be simpler than anticipated. The tiles feature pre-applied, flooring-grade adhesive, requiring only the backing to be peeled off before sticking them down. Waterproof sealer was applied around the bathroom's edges and in any cracks to ensure the tiles remained flat and to prevent water infiltration underneath. Following the floor installation, all existing handles were replaced with matte black versions to complement the new, brighter aesthetic. A new Kmart arch mirror was hung on the wall, and the space was styled with plants and various trinkets, including Kmart arch shelves and accessories, and Big W hand towels. The total budget for the makeover was meticulously tracked, with costs including $80 for Dulux paint, $96 for a box of 16 Bunnings Winton adhesive vinyl tiles, $28.30 for a pack of four Lane Black Hampton door handles, $15.05 for a Bunnings Ikonic door knob, $24.03 for a Mondella towel ring, $18.92 for a toilet roll holder, $40 for the Kmart arch mirror, $19 each for Kmart arch shelves, $10 for Kmart accessories, $4 for Big W hand towels, and approximately $40 for miscellaneous items like waterproof sealer and paint rollers. The entire project took approximately one week to complete, largely due to paint drying times. The most challenging aspect of the renovation was cutting the vinyl tiles to fit around the various skirting boards and irregular shapes in the bathroom. Despite the tiles being easy to cut with strong scissors, achieving the correct shapes required precision and effort. Teasdale expressed her satisfaction with the outcome, highlighting how the bathroom now feels cleaner, fresher, and more enjoyable. #BathroomMakeover #BudgetRenovation #DIYHomeDecor #SelfStickTiles #HomeImprovement #AffordableDesign #InteriorDesign #VinylFlooring

This article outlines the diverse range of toilets and essential accessories available, aiming to enhance the functionality, style, and ease of maintenance in modern bathrooms. The selection includes various toilet designs such as close-coupled, rimless, back-to-wall, wall-hung, and high- and low-level options, catering to both traditional and contemporary home aesthetics. The goal is to facilitate the creation of a bathroom space that is both practical and visually appealing. The range of toilets addresses different installation preferences and space requirements. Close-coupled toilets are a classic choice, where the cistern is directly attached to the toilet bowl. Rimless toilets are highlighted for their enhanced hygiene and ease of cleaning, as they lack an internal rim where germs can accumulate. Back-to-wall toilets are designed to conceal the cistern within furniture or a wall, offering a sleek, minimalist look while optimizing space. Wall-hung toilets provide a modern, floating appearance, freeing up floor space and simplifying cleaning underneath the unit. For those with specific design needs, high- and low-level toilets offer traditional styling, with the cistern positioned at a higher or lower point on the wall. Beyond the toilets themselves, the article emphasizes the importance of complementary accessories. It mentions toilet units, which can integrate the cistern into a piece of furniture, and a variety of toilet seats to suit different comfort and aesthetic preferences. Essential toilet accessories and fittings are also covered, ensuring a comprehensive selection for installation and maintenance. The article also points to bathroom clearance sections for potential savings on these items. Practical guidance is provided through a Frequently Asked Questions section. One key question addresses the installation process of a toilet, directing readers to a detailed guide for step-by-step instructions. This guide covers preparing the site, attaching the cistern and bowl, securing the unit, and connecting the water supply, with an emphasis on proper alignment and sealing to prevent leaks. Another FAQ explains how to turn off the water supply to a toilet, an essential step before any installation or repair work. This involves locating and turning the shut-off valve clockwise to stop water flow. Finally, the article tackles the common issue of condensation on toilet cisterns. It explains that condensation typically arises from temperature differences between the cold water inside the cistern and the warmer bathroom air. Solutions suggested include insulating the cistern, improving bathroom ventilation, or using dual-flush systems, which can reduce the amount of cold water used and thereby minimize condensation. These tips aim to help maintain a drier and more comfortable bathroom environment. #BathroomDesign #ToiletInstallation #BathroomAccessories #HomeImprovement #Plumbing #InteriorDesign #BathroomFixtures #DIYBathroom #HomeRenovation

This article outlines 37 DIY bathroom upgrades that can be implemented without professional assistance, emphasizing ease of installation, affordability, and significant impact on a bathroom's aesthetic and functionality. Many of these solutions are renter-friendly, allowing for temporary yet transformative changes. Key upgrades for mirrors include applying wood grain tape to create a framed look, offering a cost-effective alternative to mirror replacement. For toilet maintenance, a pumice stone cleaner is recommended for removing stubborn rings, and switch plates can be replaced to blend seamlessly with walls, requiring only basic tools. Loose plugs in outlets can be addressed with Snug Plugs, small inserts that ensure a secure fit, preventing devices like hair dryers from falling out. Surface imperfections like tile cracks can be repaired with a tile and stone repair kit, while discolored grout can be revitalized with a grout pen. For a more significant floor overhaul, peel-and-stick vinyl tiles offer a water-resistant and washable solution. Rust stains can be tackled with a specialized rust stain-removing gel, and wooden surfaces like cabinetry can be restored using wood polish and conditioner. Window treatments are addressed with cordless, no-drill Roman shades for easy installation and privacy. Alternatively, NoNo Brackets allow for curtain installation without drilling, attaching to existing blinds. For privacy without sacrificing light, window film is presented as a renter-friendly option. Light fixtures can be updated with renter-friendly Tulip shades that use double-sided tape and magnets for installation. Storage and organization solutions include expandable under-sink kits to navigate awkward plumbing and maximize space, and hair tool holders that keep counters clutter-free. Vanity drawers can be optimized with organizer sets to categorize small items. Towel hooks that adhere to surfaces are suggested for convenient placement, and a decorative clothespin towel holder offers a charming alternative to traditional racks. A toothbrush holder and dispenser system helps to tidy up the sink area. For painting projects, an eco-friendly, chalk-like paint is recommended for transforming furniture and cabinetry without the need for priming or topcoats. Shower improvements include a large, adjustable showerhead for a luxurious experience and a shower curtain liner with mesh pockets for ample storage. A self-expanding shower curtain offers more space inside the shower, preventing clingy liners. Aesthetic shower curtain hooks can also enhance the overall look. Finally, a motion-activated trash can provides a hygienic and modern update, and matte-steel cabinet pulls can refresh outdated cabinetry, ensuring the bathroom feels updated and well-maintained with minimal effort and expense. #BathroomRenovation #HomeImprovement #DIYProjects #RenterFriendly #HomeOrganization #BudgetDecor #InteriorDesign #PracticalUpgrades #SmartHome

The author recounts their persistent dissatisfaction with their apartment's shower, describing initial issues like a detached temperature handle and an awkward spout placement in a bath-shower combo. The fixed, single-stream showerhead further contributed to a less-than-ideal showering experience. Motivated to improve this crucial space without risking their security deposit, the author explored rental-friendly showerhead upgrades. During their search, the author discovered Sproos! on Instagram, a direct-to-consumer brand launched in 2020. This brand appeared to offer the desired blend of aesthetics, functionality (three spray settings), and rental-friendly installation and removal. The article focuses on the author's experience testing out a Sproos! shower kit, detailing the selection, installation, and eventual removal processes. Sproos! offers four shower models and seven color options, including recent additions like pink, green, and blue for their hand shower. The author chose "The Minimalist" in black, priced at $163, which includes a hand shower on an adjustable slide bar and a soap dish. Other models like "Stayin’ Connected" ($211) feature a magnetic phone dock and cup holder, while "Lookin’ Good" ($235) provides an anti-fog mirror and a larger shelf. A notable aspect of Sproos! products is their eco-conscious manufacturing; they are free of chrome plating, which is highly toxic, and instead use premium silicone for nozzles, high-grade anodized aluminum for the rail, and injection-molded ABS plastic for colors. The brand also offers a filter system to remove rust, silt, chlorine, chloramine, and heavy metals. The installation process was detailed, with components arriving in lightweight cardboard boxes that also served as instruction manuals via printed steps and QR codes linking to video tutorials. The kit included necessary tools such as pliers, a reusable silicone pad, biodegradable gloves, screws, Allen keys, and the brand's proprietary glue-mounting technology. The first step involved removing the old showerhead, which proved challenging due to its tight installation, necessitating the use of the provided silicone pad and pliers to prevent damage. The next phase involved connecting the new bracket, 70-inch hose, and showerhead. A minor leak occurred after initial connection, which was resolved by contacting Sproos!'s online support, who identified a missing rubber buffer. The final step, gluing the bracket to the tiled wall, was initially daunting but straightforward, utilizing a strong adhesive developed with a German brand, Tesa, which allowed for drill-free installation. The author highlights the 12-hour drying time required for the adhesive as a key consideration for planning the DIY project. After approximately 18 months, the author moved apartments and had to remove the Sproos! shower system. The showerhead hose detached easily, but the wall mount required forceful removal due to the author having misplaced the Allen key. Despite the strong adhesive, the tile remained undamaged, with residue easily cleaned off using a plastic putty knife and sandpaper. The author also discovered Sproos! offers a "moving kit" to re-install the shower bar in a new location. Ultimately, the author praises the upgrade, particularly the large round head and multiple spray settings, which significantly improved their showering experience, despite the minor initial leak and adhesive drying time. #ShowerUpgrade #DIYHomeImprovement #RentalFriendly #BathroomRenovation #SproosShower #ProductReview #HomeDecor #InstallationGuide #EcoFriendlyDesign

This article provides a comprehensive guide to selecting the ideal toilet for a modern home, considering various factors such as type, size, efficiency, and special features. It highlights the evolution of toilet designs, from basic models to high-tech options that maximize comfort, conserve water, and enhance hygiene. The author, drawing on personal experience and extensive research, presents a curated list of top-performing toilets, categorized to assist consumers in making informed decisions. The article begins by outlining the diverse range of modern toilets available, noting advancements in design, water efficiency, and smart technologies. It distinguishes between one-piece and two-piece toilets, detailing their aesthetic and maintenance differences. The discussion extends to specialized toilets, including bidet-toilet combos that integrate cleansing functions, smart toilets with automated features and advanced water-saving capabilities, and composting toilets designed for eco-conscious living without water usage. Portable toilets are also mentioned as practical solutions for non-plumbed environments like camping or RVs. Key considerations for choosing a toilet are elaborated, starting with the importance of brand recognition for ease of maintenance and access to replacement parts. Renowned brands like American Standard, Kohler, and Glacier Bay are recommended for their reliability and widespread parts availability. The article delves into the various types of toilets, explaining the construction and typical applications of two-piece, one-piece, wall-mounted, bidet-toilet combos, smart, composting, and portable models. Size and dimensions are crucial, with emphasis on standard heights, comfort heights, and rough-in measurements to ensure proper fit and accessibility. The three main bowl shapes—elongated, compact elongated, and round front—are discussed in relation to comfort and space constraints in different bathroom layouts. The article also advises on selecting appropriate toilet seats, noting their diverse materials. Water efficiency is a significant theme, with a focus on low-flow and high-efficiency toilets that use less water per flush, thereby reducing utility costs and environmental impact. The federal standard of 1.6 gallons per flush is noted, alongside options that achieve even greater savings at 1.28 gallons or less. The importance of flapper size in high-efficiency models is highlighted to prevent clogging. Different flushing technologies are explained, including gravity flush, pressure-assisted flush, and dual-flush systems, with insights into their operational mechanisms, noise levels, and water-saving potential. The innovative double-cyclone technology is also presented as a means to achieve powerful flushing with reduced water consumption. Style considerations are addressed, encouraging consumers to choose toilets that complement their bathroom's aesthetic, whether modern or vintage. The article points out that while white remains the dominant color, black and other designer colors are becoming available, as are minimalist wall-mounted designs. Additional features such as slow-close seats, heated seats, deodorizers, and LED lighting are discussed for their contributions to comfort, hygiene, and convenience. Finally, the article provides a frequently asked questions section covering practical aspects of toilet ownership, including how to measure for a new toilet, common methods for unclogging, draining a toilet, removing hard-water stains, and troubleshooting issues like continuously running toilets or malfunctioning fill valves. #ToiletReviews #HomeImprovement #BathroomRemodeling #WaterEfficiency #SmartHome #CompostingToilets #ToiletTechnology #PlumbingFixtures #HomeDesign

The founders of Home Union, Meghan Lavery and Daniel King, transformed their generic bathroom in their Williamsburg, Brooklyn, apartment by covering the walls in a vibrant array of simple ceramic tiles. This small-scale rental renovation was inspired by a surplus of tiles from their previous store, and their desire to inject bold color and personality into an otherwise bland space. They viewed the bathroom's compact size as an opportunity for extreme design, noting its potential for memorable selfies. The couple approached the tiling process with a relaxed attitude, laying out the affordable ceramic tiles in a random fashion to avoid overthinking the design. Their primary advice for anyone undertaking a similar DIY project is to meticulously prepare the workspace for easy cleanup, ensuring all tools and tiles are readily accessible. For floor tiling, they emphasized the importance of using kneepads. The entire project was completed in approximately 35 hours, spread over a week. The renovation involved a few key supplies: ceramic tiles, thin-set mortar, grout, a notched trowel, a grout float, a tile cutter, a grout sponge, drop cloths, and tile spacers. The first step, establishing the foundation, involved spreading a layer of thin-set mortar with a notched trowel and then setting the tiles one by one according to their chosen random pattern, ensuring proper adhesion and placing spacers between each tile. This process was repeated until the main area was filled, with awkward corner spaces addressed last by custom-cutting tiles as needed. After filling the entire space, the tiles were left to dry overnight. On the following morning, the tile spacers were removed, and the grouting process began. Grout was pushed into all crevices using a grout float, and excess was scraped away until the entire surface was covered. The final step, cleaning, involved using a wet grout sponge to vigorously wipe away any residue from the tiles, repeating as necessary until the surface was clean. This detailed, step-by-step approach allowed Lavery and King to achieve a significant bathroom transformation in a short period, demonstrating that impactful changes can be made even in small rental spaces with readily available materials. #BathroomRenovation #DIYProject #TileInstallation #RentalRenovation #HomeUnion #InteriorDesign #SmallSpaceDesign #HomeImprovement

This article outlines several do-it-yourself (DIY) home repair and improvement projects that homeowners can undertake with minimal effort, offering both a sense of accomplishment and potential cost savings. The article emphasizes practical advice and simple steps for common household issues. The first section focuses on toilet repairs, specifically addressing issues with fill valves and flappers. It explains that constant running water often indicates a problem with these components. The repair process involves shutting off the water, draining the tank, and then replacing the faulty valve or flapper, noting that these parts are inexpensive. Next, the article discusses bathroom caulking. It advises against caulking over existing dirty caulk and suggests using an X-ACTO knife to remove old, discolored caulk, often a sign of mold and mildew. Homeowners should then apply 100% silicone-based caulking, which is water-resistant and durable, smoothing it with a finger and cleaning up excess as they go. For picture hanging, the article provides guidance on situations where wall studs are unavailable. It recommends using drywall anchors designed to hold adequate weight, rather than the flimsy anchors often included with frames. The process involves drilling a small hole, installing the anchor snugly, and then tightening the screw an additional five to ten turns to secure the anchor behind the drywall. For better weight distribution, it is suggested to use two anchors, measuring from the floor for even alignment. Additionally, placing a metal washer under the screw for pictures with hanging wire is advised to enhance security. The article then moves to LED lighting, highlighting canless LED lights as a stylish, brighter, more energy-efficient, and easier-to-install alternative to traditional recessed lighting. These lights come as a single unit (housing, trim, and light) and can be installed over existing recessed cans. Retrofit models screw into the existing socket, eliminating the need for complex wiring. A crucial safety tip is to ensure the power is off and to use an electric tester before installation. Garbage disposal issues, particularly when the unit hums but doesn't grind, are often due to clogs. The article suggests two methods for clearing obstructions: a 'top down' approach where one removes the obstruction directly from the disposal's opening (after unplugging for safety), or a 'bottom up' method using a hex wrench to jiggle the flywheel from underneath. Taping the hex wrench to the disposal for future use is a practical suggestion. Regarding dishwashers, the article advises homeowners to first clean the filter and drain basket according to the manual, as no tools are typically required for this. If that doesn't resolve the issue, checking and clearing the air gap hose or the hose connected to the disposal is recommended. When reattaching the hose, it's important to ensure a high loop above the disposal to prevent food waste from flowing back into the dishwasher. The article also covers door adjustments, explaining that as houses settle, doors can become misaligned. For minor misalignments, filing the latch or creating a bigger opening in the door jam can be effective. For more serious issues, adjusting the strike plate vertically or horizontally by loosening and re-screwing it is suggested, with a note to be careful not to create new holes. The author recommends watching instructional videos before attempting any of these repairs, even for experienced DIYers, to refresh memory and ensure proper execution. This blog post aims to empower homeowners to confidently tackle basic home repairs, promoting self-sufficiency and resourcefulness. Another section details retractable gates as a safer alternative to pressure-mounted safety gates, especially for homes where walls may not be perfectly aligned. Retractable gates, available in wood, metal, or rubber, are easy to screw in. The article specifically recommends rubber gates, citing their ability to prevent bruising if a child falls into them, compared to metal or wood options. Finally, the article touches on changing car batteries, presenting it as a task accessible to anyone who follows basic wiring and safety rules. The proper procedure involves disconnecting the negative (black) wire first, followed by the positive (red) wire, then lifting out the battery by its handle. When installing a new battery, the wires should be connected in reverse order: positive first, then negative. Emphasizing safety, the article warns against touching the battery directly to avoid contact with potentially leaking acid and advises taking time during the process due to the significant energy involved. #HomeDIY #HomeImprovement #HomeRepair #DIYProjects #HouseholdMaintenance #ToiletRepair #BathroomCaulking #PictureHanging #LEDLights #GarbageDisposal #DishwasherMaintenance #DoorAdjustment #RetractableGates #CarBatteryReplacement