Has Philips Hue revised the dimmer switch again?

The second-generation Philips Hue Dimmer Switch offers significant improvements over its 2015 predecessor, addressing its dated feel with a more contemporary design and enhanced functionality. The updated switch features a new 'Hue' button, time-based light scene modes, and a larger, more versatile wall plate, while retaining the original's HomeKit configurability and an affordable $25 price point. Physically, the new Dimmer Switch measures 3.6 x 1.4 x 0.3 inches, similar in size to the original without its wall plate. However, its design has been refined with more rounded corners and a matte finish, replacing the older model's boxy shape and shiny appearance. The button layout has also been revised, shifting from four distinct 'on,' 'brighter,' 'dimmer,' and 'off' buttons to a combined 'on/off' button, a brightness up/down rocker, and the new 'Hue' button. This configuration effectively provides an additional customizable button. The wall plate has also undergone a redesign, now featuring a matte finish and a mid-size dimension of 4.88 x 3.13 inches, an increase from the standard 4.5 x 2.75 inches of the previous model. It comes in two snap-together pieces, with the rear section offering both peel-and-stick adhesive and six mounting holes for screw installation. A notable change is the relocation of the magnets from the wall plate to the switch itself, allowing the switch to attach to any metal surface, such as a refrigerator or lamp pole. The new Dimmer Switch uses a CR2032 coin cell battery, promising two years of battery life. Installation is straightforward, utilizing either the wall plate's adhesive backing or screws. Setup is completed through the Hue mobile app, which quickly identifies and connects the Zigbee-enabled switch to a Hue Bridge. A Hue Bridge is essential for operation, meaning users controlling Hue lights via Bluetooth will need to acquire one. The switch can be configured to control specific rooms, zones, or individual lights. The new 'Hue' button is a key enhancement, offering two modes: 'scene cycle' and 'time-based' light. In scene cycle mode, users can program up to five lighting scenes to cycle through with each press of the Hue button. The time-based light mode allows for different scenes to activate depending on the time of day, with five three-hour time zones configurable to trigger specific light settings, such as warm light at sunrise or a night light at midnight. While the 'power on' functionality is configurable to either resume the last-used scene or trigger a specific scene, the 'power off' behavior is fixed, always turning off controlled lights. The central dimmer rocker maintains its primary function of brightening or dimming lights, and its controls remain non-configurable through the Hue app. For more advanced customization, the switch fully integrates with HomeKit, allowing all four buttons (HomeKit counts the rocker as two) to trigger any HomeKit scene, automation, or control compatible smart devices, significantly expanding its utility as a control panel for a broader smart home ecosystem. Overall, the revamped Philips Hue Dimmer Switch successfully addresses the shortcomings of its predecessor, offering a more refined, modern, and functional design. Its ease of installation, setup, and robust HomeKit compatibility remain strong features, making it a highly recommended accessory for existing Philips Hue users with a bridge seeking an upgraded control experience. #PhilipsHue #SmartHome #DimmerSwitch #HomeKit #SmartLighting #HomeAutomation #TechReview #SmartGadget #Zigbee

The Philips Hue Dimmer Switch is a highly regarded device, with the reviewer owning five units. While the reviewer has not fully adopted the entire Hue product ecosystem, they utilize a Hue Bridge (2nd generation), a Hue Go light, several dimmer switches, and eight warm white Hue bulbs. The primary motivation for using these dimmer switches is to enable control of smart bulbs in areas frequented by family members who might otherwise use traditional light switches, which would disconnect the smart bulbs from the Hue system and Apple HomeKit. The packaging for the Hue Dimmer Switch is made of fairly thin cardboard with an inner plastic frame that suspends and protects the device, ensuring it remains undamaged during transit. The switch itself consists of two main parts: a base plate for wall attachment and a remote-like switch. The switch is held in the base plate by magnets, allowing it to function as a removable remote or to be magnetically attached to other metal surfaces, such as a refrigerator. Alternative mounting options include 3M adhesive strips for permanent placement or screws via two pre-drilled holes in the base plate. These multiple attachment methods offer flexibility for users. The design of the switch and base plate is described as unobtrusive and stylish, blending well into various environments without being overly conspicuous. The dimmer switch is powered by a CR2450 coin battery, estimated to last between 12 and 24 months, depending on usage. The device has a projected lifespan of 50,000 presses, which translates to nearly 14 years with an average of 10 presses per day. It's noted that there are different versions of the switch available, some with 'ON' and 'OFF' labels and others with universal symbols (a vertical line for 'ON' and a circle for 'OFF'), though both versions function identically. Setting up the Philips Hue Dimmer Switch requires the 2nd Gen Philips Hue Bridge. Philips offers various starter kits that include the Bridge, bulbs, and/or the dimmer switch for new users. Initial setup is performed through the Hue app, which then provides an option to program the switch via the Apple Home app. This integration with HomeKit is a significant feature, as it allows the dimmer switch to control not only Philips Hue lights but also other HomeKit-enabled lighting products (e.g., LiFX, Koogeek) and virtually any HomeKit-compatible device. Users can program the four buttons to turn devices on or off, adjust brightness, or activate specific scenes involving multiple actions. Advanced functionality is available through third-party HomeKit apps, which support conditionals. Conditionals enable the switch to perform different actions based on parameters like the time of day. For example, the 'on' button could activate a smart fan during specific hours and control a different device at other times. While these conditional options offer extensive customization, the article also highlights that using the switch strictly with Hue lighting provides additional exclusive features, such as actions triggered by multiple presses or long presses. The reviewer concludes that the Philips Hue Dimmer Switch is a preferred choice for controlling both Hue and HomeKit devices due to its portability, programmability, and versatile placement options, even though it does not replace hardwired in-wall switches. #PhilipsHue #DimmerSwitch #SmartHome #HomeKit #SmartLighting #WirelessSwitch #HomeAutomation #ProductReview

As someone who prefers simplicity and initially hesitated to adopt smart home technology, the author decided to explore Philips Hue smart bulbs as an alternative to installing a traditional dimmer switch. The primary motivation was the bulbs' out-of-the-box dimmability and compatibility with most light fixtures. The author purchased a four-pack of soft white light bulbs, installing one in the living room and another in their youngest daughter's bedroom. After using them for a period, the author expressed satisfaction with the ease of setup and the comprehensive features offered by the accompanying app. The setup process for the Philips Hue light bulbs is straightforward, involving a Bluetooth connection to a smart device. Users download the Philips Hue app, scan a QR code on the lightbulb, and assign it to a specific room. Once connected, the app enables various controls, including toggling power, dimming lights, utilizing preset light intensities, and setting timers or routines for automatic activation and deactivation. The app also allows for simultaneous or independent adjustment of lighting in multiple rooms. While the initial intent was to use the dimmability feature as a replacement for a dimmer switch, the author found the "Routines" feature to be the most favored. This functionality allows users to schedule lights to turn on or off at predetermined times. For instance, in the daughter's room, a routine was established to gradually dim the lamp 30 minutes before bedtime, turning off completely at 9:30 p.m., creating a conducive environment for sleep. However, it is noted that without the optional Philips Hue Bridge, these routines require manual activation daily, limiting full automation. Beyond dimming and routines, other notable features include a nightlight setting, which provides a very low level of illumination, and a candle setting, designed to emit a soft, flickering glow. A timer feature is also available, where the lights flash and then turn on or off once the timer concludes. The Bluetooth-enabled setup permits control of each lightbulb from a smart device within a 30-foot range. The smart bulbs also integrate with popular voice assistants such as Siri, Google Assistant, and Amazon Alexa. For enhanced control and full automation capabilities, the Philips Hue Bridge can be added, supporting up to 50 Philips Hue lights and devices, and enabling remote control from any location with an internet connection. #PhilipsHue #SmartBulbs #HomeLighting #SmartHomeTech #DimmableLights #HomeAutomation #LEDLighting #ProductReview

This article provides a comparative analysis of three Philips Hue smart switches: the classic dimmer switch, the compact Smart Button, and the versatile Friends of Hue switches. Each switch offers distinct features and applications within a smart home lighting system. The Philips Hue dimmer switch, a classic choice, is noted for its affordability and ease of use. Priced under 20 euros, it offers intuitive control over lighting. The ON button cycles through five pre-configured scenes, while dedicated buttons allow for dimming and switching off lights. Its design includes a magnetic mounting plate, enabling it to be attached to surfaces or used as a portable remote. The article highlights that third-party applications like iConnectHue can further enhance its functionality by enabling long keystroke actions and custom dimming levels. The dimmer switch is recommended for individual rooms or controlling specific lighting zones due to its versatility and simple installation. The Philips Hue Smart Button, currently an Amazon exclusive, costs between 20 and 25 euros. Despite its smaller size, it aims to replicate the dimmer switch's capabilities. A single press can cycle through five scenes, and a subsequent press after a brief pause turns off the lights. A long press can dim lights or switch off all lights in the house. The Smart Button comes with a square mounting plate designed to fit an empty switch box or adhere to smooth surfaces, and a magnetic sticker allows for flexible placement. While its configuration options are more limited compared to the dimmer switch, third-party apps can still customize its behavior, such as reducing the number of active scenes. The Smart Button is suggested for single rooms, valued for its aesthetic appeal and flexible mounting options, though its operation is described as less intuitive than the dimmer switch. Friends of Hue switches stand out due to their batteryless Enocean module, which generates energy with each press. These switches are available from various manufacturers like Gira and Busch-Jaeger and are designed to integrate seamlessly with existing light switch installations. Each Friends of Hue switch features two rockers, each with two buttons, allowing for combined presses. With the ability to differentiate between short and long presses, these switches can be configured for up to twelve different actions, though extensive customization requires third-party apps, as the native Hue app offers limited configuration. They can be mounted on empty flush-mounted boxes or smooth walls, and can be installed alongside existing light switches using a larger frame. Despite being the most expensive option, Friends of Hue switches are considered the most visually discreet and powerful solution, ideal for individual rooms or open-plan areas with multiple lights or zones. The article notes that a noticeable clicking sound accompanies each press due to their energy-harvesting mechanism. Ultimately, the choice among the three depends on specific needs for functionality, aesthetics, and budget within a smart home environment. #PhilipsHue #SmartLighting #SmartHome #DimmerSwitch #SmartButton #FriendsOfHue #HomeAutomation #LightingControl #HardwareComparison

The Philips Hue Dimmer Switch is a versatile smart home device capable of controlling more than just Philips Hue smart bulbs. By integrating it with Apple's HomeKit platform, users can assign various functions to its four buttons, allowing for comprehensive control over a wide range of HomeKit-enabled devices. This guide details the process of configuring the Hue Dimmer Switch within HomeKit, transforming it into a personalized control panel for a smart home ecosystem. The primary motivation for integrating the Dimmer Switch with HomeKit often stems from a desire for more granular control than the standard Hue settings offer. For instance, the default Hue app might not allow users to customize the specific 'off' behavior of the Power button. By shifting control to HomeKit, each of the four buttons—Power, Hue, and the two dimmer buttons—can be individually configured to trigger specific scenes or control distinct accessories. This enables scenarios where the Power button activates a desired light scene without a default on/off toggle, and the dimmer and Hue buttons manage separate lighting configurations. Beyond lighting, a HomeKit-configured Hue Dimmer Switch gains the ability to control virtually any compatible smart device. This includes smart plugs, air purifiers, smart locks, and even televisions. The flexibility offered by HomeKit allows users to create a centralized control point for diverse smart home functionalities. However, there are specific prerequisites and trade-offs associated with this HomeKit integration. A crucial requirement is the possession of a Hue Bridge. While newer Hue smart lights might support Bluetooth control without a Bridge, the Dimmer Switch necessitates the Bridge for HomeKit connectivity. Existing Hue users are likely to already own this device. Furthermore, configuring the Dimmer Switch in HomeKit means relinquishing all configuration options within the native Hue app. This includes advanced features such as time-based light scenes and the ability to assign multiple actions to successive button presses (second, third, fourth, or fifth presses). While HomeKit does support double- and long-press options for some smart switches, the Hue Dimmer Switch is not among them for these advanced functionalities. Similarly, HomeKit's ability to configure time-of-day options for button presses is limited to a single time-of-day setting, making it less robust than the Hue app's multi-time period options. This guide assumes the user already possesses a Hue Dimmer Switch (either first or second generation) and a Hue Bridge. For those new to the Hue ecosystem, consulting a review on how to add the dimmer switch to a Hue setup is recommended prior to HomeKit integration. The customization process begins within the Hue app. Users navigate to Settings > Accessories, select the desired dimmer switch, and then tap 'Set up in Apple Home.' A warning will appear regarding the removal of the current Hue configuration, which users must confirm. Subsequently, the Apple Home app is launched, where the dimmer switch's icon can be long-pressed to access its button configuration. Each button (labeled Button 1, Button 2, etc.) can then be assigned to trigger HomeKit scenes or control specific accessories. Users can select multiple scenes or accessories and then fine-tune their behavior. For instance, if controlling a HomeKit-enabled TV, users can specify whether the button turns it on or off or switches to a particular input. An optional 'Turn Off' setting allows for automatic deactivation after a specified period, ranging from 'Never' to 'After 4 hours.' The 'Test This Action' feature allows users to verify the configuration before finalizing. Once satisfied, the settings are saved, and the process can be repeated for other buttons. It is always possible to revert to Hue app management by reconfiguring the dimmer switch within the Hue app. #PhilipsHue #HomeKit #SmartHome #DimmerSwitch #HomeAutomation #SmartLighting #AppleHome #TechTutorial #SmartDevices

This article discusses the Philips Hue Tap Dial switch, focusing on the new mini mount version. The Philips Hue Tap Dial switch was recently released with an updated mini mount, offering a more compact alternative to its predecessor. While the core functionality of the switch remains unchanged, the new mount distinguishes itself with a smaller diameter of 4.8 centimeters, compared to the previous mounting plate's 8x8 centimeter dimensions, which were designed to fit standard European flush-mounted boxes. A key point of interest for potential buyers is the exclusive retail model for this specific version: the Hue Tap Dial with mini mount is sold solely through the Philips Hue online shop, making it unavailable through other retailers. This exclusivity also means that its price of 49.99 euros is not subject to competitive changes in the immediate future. The packaging of the new model further reinforces this distribution strategy, being notably compact and lacking a hanger, which suggests it is not intended for typical retail shelf display. From a qualitative perspective, the mini mount is presented favorably. It is crafted from metal and designed for easy adhesive application to smooth surfaces. A notable difference from the larger mount is the absence of a small protrusion meant to perfectly align the switch, a feature whose impact on user experience is acknowledged as subjective. The design ensures that once installed, only the switch itself is visible, with the mini mount being completely concealed. The Hue Tap Dial Switch provides extensive control capabilities, including the ability to manage multiple scenes within a single room or across different rooms. It also allows for distinct actions based on short or long button presses. The device's standout feature is its rotary wheel, primarily used for dimming lights. This wheel can also be utilized to switch lights on and off within a room. A point of user dissatisfaction arises when the rotary wheel is used with multiple rooms. In such scenarios, the rotary function must be assigned to a specific room or zone, preventing its application to other rooms controlled by the buttons. This limitation suggests a potential area for improvement, with a proposed solution being the ability for the rotary wheel to dim the last activated room. However, this raises questions about its functionality when no lights are currently on. Despite these minor criticisms, the article generally praises the enhanced capabilities offered by the four buttons and the rotary wheel. When compared to other Philips Hue control devices like the Hue Smart Button or Hue Dimmer Switch, the Tap Dial Switch is noted for its advanced features. Although it is not the cheapest option, its price point of 49.99 euros is considered reasonable, falling just below that of Friends of Hue switches, suggesting a fair balance between cost and functionality for the smart home enthusiast. #PhilipsHue #SmartLighting #TapDialSwitch #MiniMount #SmartHome #HomeAutomation #LightingControl #ProductReview #ExclusiveProduct

The Philips Hue Wall Switch Module is a new device designed to integrate traditional wall switches into the Philips Hue smart lighting ecosystem. Priced at $39.95, this module addresses a common issue faced by smart bulb users: the loss of smart control when a physical wall switch is turned off. By making existing wall switches "Hue-smart," it ensures that Hue lightbulbs remain powered and controllable through the Hue app and other smart home platforms, even when the physical switch is toggled. The module functions essentially as a buttonless Zigbee remote control for Hue lights, allowing any standard household light switch to manage Hue lighting. It operates on a single CR2450 coin battery, which Philips Hue claims will last for at least five years, mitigating frequent battery replacement concerns. Installation of the Hue Wall Switch Module is designed to be straightforward, typically taking about fifteen minutes, provided there is adequate space in the existing wiring box. Users need to be comfortable working with household electricity or should consult an electrician for installation. The process involves disconnecting the original electrical wires from the light switch, rerouting them to a provided wire connector to maintain constant power to the lightbulb socket, and then connecting the Hue Module to the light switch using Hue-provided wires. The module requires a Hue Bridge to function and is added to the Hue app like any other Hue accessory. It can be configured to control multiple Hue lights in a room or zone and allows the switch to function as a simple on/off toggle or to cycle through predefined Hue scenes with multiple presses. While the module effectively solves the problem of smart bulbs becoming unresponsive when a physical switch is off, it does have some limitations. One minor issue noted during testing was an occasional inconsistency in switch orientation, where flipping the switch up might turn the light off instead of on, suggesting a 5% failure rate in accurately registering the switch position. Additionally, the Hue app does not currently support configuring the Wall Switch Module to automatically turn off lights after a set time, which could be a useful feature for certain areas like a laundry room. For this, an additional motion sensor might be necessary. It’s important to note that the Hue Wall Switch Module only works with Hue lightbulbs and cannot control standard, non-smart bulbs, setting it apart from other smart switches on the market. However, it does support both single and double rocker switches, as well as push-button switches which allow for dimming capabilities. The Philips Hue Wall Switch Module acts as a bridge between users who prefer the advanced features of smart bulbs, such as color and dimming control, and those who value the tactile and aesthetic aspects of traditional wall switches. It provides a solution for integrating physical controls without sacrificing smart functionality, appealing to users deeply invested in the Philips Hue ecosystem. For those not committed to Hue bulbs, alternative Zigbee or Z-Wave solutions exist that can convert standard switches into smart ones capable of controlling regular lights. Overall, the module offers a refined solution for smart home enthusiasts looking to enhance their Hue lighting experience, albeit with an added cost and a slight learning curve for installation and nuanced operation. #PhilipsHue #SmartHome #WallSwitchModule #SmartLighting #HomeAutomation #TechReview #Zigbee

The Philips Hue Tap Dial switch is introduced as a powerful and innovative smart lighting controller aimed at "Hue superusers." Priced at $49.99, this wireless, battery-operated device features four buttons and a physical dial for dimming lights and setting scenes. Unlike the simpler Hue Smart Dimmer Switch, which costs about half the price, the Tap Dial is designed for controlling multiple zones or an entire house filled with Philips Hue lights. The switch is built with a weighty, solid feel, similar to a Nest Learning Thermostat, ensuring it stays put when operated on a surface. Its dimming action is described as smooth and responsive, without noticeable lag. The default setup in the Hue app assigns buttons one through three to adjust light levels, and button four to cycle through five pre-set Hue scenes. A long press on any button turns the lights off. The dial provides precise dimming capabilities. While its out-of-the-box configuration is for a single room or zone, the Tap Dial's true potential lies in its ability to act as a multi-zone controller for users with extensive Hue light installations. The article describes a personal setup where the Tap Dial was programmed to control different areas of a house: button one for all lights, button two for the entry hall and living room, button three for upstairs lights, and button four for downstairs lights. It also notes the ability to assign up to 10 additional scenes per button press. A current limitation highlighted is the dial's inability to dynamically dim or brighten lights based on the last-pressed button, instead requiring it to control either all lights or a single pre-defined zone. This necessitates a workaround of using subsequent button presses to adjust lights not controlled by the dial. Despite this, the convenience of having a central physical controller for all household lights, eliminating the need for a phone or voice commands, makes the device highly useful for those fully invested in the Hue ecosystem. However, the author notes that without a complete Hue setup, the Tap Dial remains a "nice-to-have" rather than a "must-have," especially given its price and the additional requirement of a Hue Bridge ($59.99) due to its Zigbee protocol. Comparatively, the cheaper Hue Smart Dimmer is suggested for users with fewer Hue bulbs, as it offers similar core functionalities but with a less refined dimming interface and time-based lighting features currently absent from the Tap Dial (though promised soon). The Tap Dial is also contrasted with the Lutron Aurora, another dimming option for smart bulbs. Privacy considerations are also addressed, detailing the data collected by Philips Hue and Signify, and their stated policies on data usage and protection. Future updates are anticipated, including broader compatibility with Amazon Alexa and the smart home standard Matter. Matter support would enable the Tap Dial to control a wider range of smart devices from various manufacturers, moving beyond the proprietary Hue ecosystem. However, the article advises against purchasing the device solely based on future capabilities, recommending it primarily for current Hue superusers seeking a dedicated physical control solution. #PhilipsHue #SmartHome #SmartLighting #HomeAutomation #TapDial #MatterStandard #SmartSwitch #HueBridge

The Wemo Wi-Fi Smart Dimmer Light Switch is reviewed as a key component for home automation, aiming to simplify daily living through smart technology. The device arrives in packaging designed with a unique aesthetic, featuring a standard cardboard exterior with white graphics that display the Wemo logo, a line drawing of the dimmer, and humorous, suggested dimmer settings. The interior of the box is a vivid green, housing the dimmer switch and a comprehensive instruction manual titled “Let’s go.” This manual is noted for its clear graphics and straightforward text, guiding users, even novices, through the installation process which involves home wiring. The kit includes all necessary accessories such as wire nuts and labels to ensure a safe and correct installation. The installation process involves replacing an existing light switch, specifically a hallway ceiling lamp switch in the reviewer's case. A critical observation during installation is the Wemo Dimmer's larger size compared to a standard switch, which might pose a challenge if the electrical switch box is already crowded with wires. Careful tucking of wires and ensuring wire nuts remain secure are advised. The reviewer emphasizes safety, recommending that individuals uncomfortable with home wiring seek assistance from a knowledgeable friend or a professional electrician. After installation and power restoration, the dimmer indicates readiness with a sequence of flashing lights, settling into a flashing blue. Setting up the smart functionality is achieved via a dedicated app. The process is described as seamless, involving connecting the phone to the Wemo Dimmer’s Wi-Fi network, selecting the bulb type, pairing with voice assistants like Alexa, and integrating with the home network. No difficulties were encountered during this setup. Once configured, the dimmer allows for voice commands to control the light, including turning it on or off and adjusting brightness levels via Alexa. The app offers extensive control over the lighting, accessible both on the home network and remotely via cellular 4G, with minimal delay observed even when tested through a VPN in Thailand. Further functionalities available through the app include setting timers, scheduling automatic light turn-offs after a specific duration, and activating an “Away” mode that randomizes light activity for enhanced home security. The dimmer also supports integration with IFTTT, offering potential for further automation possibilities. The overall experience with the Wemo Wi-Fi Smart Dimmer Light Switch is highly positive, praising its ease of use, broad functionality, and reliability. The reviewer expresses a desire to equip an entire home with these dimmers. An update six months after the initial review confirms continued satisfaction, highlighting the family’s enjoyment of Alexa integration and a custom IFTTT applet that automatically turns on the light when the garage door opens, preventing entry into a dark house. The product is valued for contributing significantly to a more automated and convenient home environment. #Wemo #SmartDimmer #LightSwitch #HomeAutomation #WiFiControl #AlexaIntegration #SmartHome #ProductReview #LightingControl

The increasing popularity and affordability of LED light bulbs have led to a surge in products, necessitating thorough testing, particularly concerning their dimming capabilities. A common issue observed in many dimmable LEDs is flickering and buzzing when adjusted to lower light settings. This phenomenon is extensively documented through a series of GIF-animated demonstrations. The Saffron LED, a 40W replacement bulb, closely mimics the appearance of traditional incandescents. However, it exhibits severe flickering when dimmed, resembling a strobe light, despite not being officially rated for dimmability. Its $10 price point suggests it should offer better performance in this regard. Another problematic product is the Feit 40W Replacement LED, which, despite being advertised as dimmable, also produces an undesirable flickering effect. In contrast, Osram's 40W and 60W replacement LEDs show slightly better, though not perfect, dimming performance, with a minor, less noticeable light waver at low settings. The Green Creative Titanium LED (Series 4.0) offers a marginal improvement in dimming, with barely perceptible flicker at low settings. However, earlier models like the Switch Infinia LED, while innovative with its liquid-filled design for heat management, suffered from significant flickering and have since been discontinued. Philips' SlimStyle LED also initially presented dimming issues, including flicker and an audible buzz, prompting a shift in testing methodology to GIF animations for better visualization. Subsequent iterations, such as the Philips SlimStyle 75W Replacement LED, demonstrated improved dimming performance with reduced flicker and eliminated buzzing. BR30 floodlight-shaped LEDs from Philips and GE, designed for dimmer compatibility, largely failed to perform adequately, exhibiting considerable flickering. An exception is the GE Reveal BR30 LED, which stands out for its exceptional dimming performance and superior color quality, earning it an Editor's Choice award. Cree's BR30 floodlight, however, proved to be overly flickery, prompting anticipation for its second-generation model. More affordable options, like the Cree 4Flow LED, offer impressive, steady dimming at low settings, making them a commendable choice. Similarly, 100W replacement LEDs from Cree and Philips also demonstrated satisfactory, flicker-free dimming. The GE 100W Replacement LED likewise performed well, suggesting that higher wattage bulbs, often commanding a higher price, might allow manufacturers more flexibility to integrate better dimming components. Conversely, the Utilitech 100W Replacement LED failed the dimming test, highlighting inconsistencies across manufacturers. Continuous testing and review of LED light bulbs are crucial to ensure that efficiency upgrades do not compromise dimming quality, guiding consumers toward reliable products and away from those with performance issues. #LEDLighting #SmartHome #LightBulbs #DimmerSwitches #HomeAppliances #ConsumerElectronics #ProductReview #EnergyEfficiency #HomeAutomation

The Lutron Aurora is a smart bulb dimmer designed to address common frustrations experienced by users of Philips Hue connected lighting systems. Connected bulbs require the traditional wall switch to remain in the "on" position to maintain connectivity, leading to issues when the switch is inadvertently flipped off. The Aurora, priced at $40, provides a solution by acting as both a light controller and a safeguard against accidental switch-offs. The device consists of a bracket that screws over a standard toggle light switch, securing it in the "on" position. A rotary knob then clicks onto this bracket. Users can press the knob to turn lights on or off, and rotate it to adjust brightness, mimicking the intuitive operation of a traditional dimmer. This design ensures that the smart bulbs remain powered and controllable through the smart home system, regardless of manual interaction with the Aurora. Installation of the Lutron Aurora is noted for its simplicity, not requiring complex wiring or a deep understanding of DIY home improvement. This ease of installation makes it particularly appealing for renters or individuals who prefer not to alter their existing electrical infrastructure. The product’s non-destructive mounting means it can be easily removed without leaving permanent marks. The Aurora integrates with the Philips Hue ecosystem, capable of connecting to a second-generation (square) Hue Bridge to control up to 50 lights or multiple rooms. For those without a Bridge, the knob can directly pair with up to twelve Hue bulbs, though with fewer control options. Utilizing Zigbee 3.0, the Aurora theoretically supports other smart bulbs compatible with this wireless standard, with Lutron actively pursuing broader compatibility. While the Aurora offers a seamless experience for controlling Hue lights, it is limited to controlling lighting and cannot manage other smart home devices like blinds. A potential drawback is its compatibility solely with toggle-style switches, excluding flat-style switches. Furthermore, its price point of $39.95 is on the higher side compared to some alternative smart switches or even a set of four white Hue bulbs, and it costs more than voice control devices like the Echo Dot or Google Home Mini. Competitors in the smart switch market often necessitate more involved installation processes, typically requiring electrical modifications that can be a barrier for many consumers. Philips' own Hue Tap and Smart Dimmer Switch offer alternative control methods at different price points, but neither provides the Aurora's unique solution for preventing accidental power cuts to smart bulbs. The Hue Tap, while cheaper and battery-free, lacks dimming functionality, and the Hue Smart Dimmer Switch, though offering similar controls, does not secure the traditional switch. Despite its cost, the Lutron Aurora is lauded for its ability to solve a specific and common problem in smart lighting setups with an elegant, user-friendly, and non-permanent solution. Its combination of easy installation, intuitive operation, and problem-solving design makes it a valuable addition for Philips Hue users seeking a more reliable and conventional control experience. #LutronAurora #PhilipsHue #SmartLighting #SmartHome #HomeAutomation #LightDimmer #Zigbee3 #SmartSwitch #HomeTechReview

Philips Hue introduces a new Slim recessed light, addressing previous challenges of installation depth and cost associated with their older models. This review focuses on the larger version, which measures 170 millimeters in diameter and is priced at 109.99 euros. This new design requires significantly less installation depth, making it suitable for ceilings with limited cavity space. Previously, Philips Hue recessed spotlights necessitated a 10-centimeter cavity, but the Slim version requires a minimum of 4.5 centimeters, primarily to accommodate its 3.5-centimeter transformer. The article compares the Philips Hue Slim recessed light with two alternative ZigBee-compatible options. The first is the Paulmann Areo recessed panel, which has similar dimensions but offers only White Ambiance technology (no color) and a maximum brightness of 1,200 lumens. The Paulmann panel protrudes by 1.2 centimeters from the ceiling, and despite its 175mm lamp size, requires a smaller hole cut-out of 50 to 140 millimeters. Its list price of 92.49 euros is comparable to the Philips Hue offering, but without the color functionality. The second alternative is a non-branded ZigBee product that includes color capabilities, priced at 52.95 euros. This no-name option provides up to 1,100 lumens and covers a white color temperature range of 2,700 to 6,500 Kelvin, while the Paulmann panel covers 3,000 to 6,500 Kelvin. In contrast, the Philips Hue Slim recessed light offers superior technical specifications. It can produce up to 1,500 lumens at 4,000 Kelvin, representing a 36 percent increase in brightness compared to the non-branded product. It also covers a broader color temperature range of 2,000 to 6,500 Kelvin, making it ideal for creating various ambiances, including cozy scenes with warm white light. The extremely flat design of the light, measuring only 2.5 centimeters from the frame to the end of the spring, contributes to its versatility. The internal design of the Philips Hue Slim recessed light is notable. The LEDs are positioned horizontally, shining at a 90-degree angle, rather than directly downwards. A diffuser and a simple white plastic film are used to redirect the light effectively, ensuring even illumination without visible individual LED points, a crucial feature for its low overall height. The wiring process is simplified by a clamp connection, and the incoming 230V cable is securely fastened. Small cooling fins on the side of the housing help manage heat, and the illumination is consistently even across the surface. Overall, the Philips Hue Slim recessed lights represent a significant improvement over previous models like Milliskin or Xamento, which typically housed GU10 spotlights. While still positioned within the premium Hue price range, they offer enhanced functionality and performance for their cost. The 90-millimeter version, with up to 1,000 lumens, is priced at 89.99 euros, while the larger 170-millimeter model provides even greater brightness at 109.99 euros. Both sizes are available with either a white or black frame and are expected to be available through independent retailers, potentially leading to competitive pricing. The article concludes by noting that the ZigBee radio is located directly in the light housing, not in the power brick, and that the product has an IP44 rating, making it suitable for environments like bathrooms. #PhilipsHue #SmartLighting #RecessedLighting #HomeAutomation #LEDLighting #ProductReview #ZigBee #HomeDesign #LightingTechnology

This article details the new Philips Hue products launched in June 2024, focusing on their features, design, and intended use. Among the significant releases is the Philips Hue Twilight, a bedside lamp available in black and white with a cork base. This lamp integrates ColorCast technology for gradient effects and dual light sources, offering up to 1,380 lumens. It includes an automatic 'go to sleep' function and supports extremely low dimming levels, aiming to enhance sleep and overall well-being. Philips Hue also introduced new slim recessed lights for the European market, addressing the need for fixtures with reduced installation depth. These are available in 90mm and 170mm diameters, providing up to 650 lumens and 1,100 lumens, respectively, with a 105-degree beam angle. Their thin profile makes them suitable for spaces with low ceilings, offering versatile lighting solutions. A notable addition is the Philips Hue Datura LED panel, an evolution of previous models. It features a frameless design with separately controllable LEDs for both direct and indirect lighting, capable of producing up to 4,850 lumens. The Datura panel is designed to create diffuse backlighting and powerful front illumination, coming in four variants. For flexible lighting, the new Philips Hue Solo Lightstrip is introduced in 3, 5, and 10-meter lengths. This lightstrip can be shortened but not extended, offering comparable brightness to the Lightstrip Plus at a lower price point. It features RGBWW LEDs and up to 1,700 lumens, making it a cost-effective option for various projects. The article also announces the return of several Philips Hue Lightguide models—Triangular and Globe—alongside the existing Ellipse. Two new smaller models, Edison and small Globe, are launched, bringing the total Lightguide variants to five. These bulbs are designed as decorative elements with reflective glass coatings, offering vibrant colorful light and dimming capabilities. A specially designed 3D-printed table lamp for the Lightguide bulbs is also available. Furthermore, the GU10 spotlights have received a significant upgrade, now offering over 50 percent more brightness in standard white (2,700 Kelvin). The White Ambiance and White and Colour Ambiance models now reach up to 400 lumens with cooler white tones. Finally, the Philips Hue Tento, a streamlined version of the Datura, is set to be released. This ceiling panel features a single light source with a transparent cover that allows some light to shine towards the ceiling. It will be offered in affordable White, White Ambiance, and White and Colour Ambiance versions, providing smart lighting for various areas like closets, garages, and hallways. #PhilipsHue #SmartLighting #HomeAutomation #LEDLighting #ProductLaunch #LightingDesign #HomeDecor #SmartHome

The TP-Link Smart Wi-Fi Light Switch Dimmer (model HS220) is an in-wall smart dimmer switch designed for home use. The device features a sophisticated and stylish design, with a large rocker switch for on/off control and gradual dimming. Two smaller buttons located above the rocker allow for setting maximum brightness and manual adjustment of light levels. A row of LEDs visually indicates the brightness setting, while a color-coded LED within the paddle displays the switch’s Wi-Fi status. While the switch itself is well-designed, the accompanying wall plate has some notable drawbacks. It is significantly larger than standard wall plates, measuring 5 x 3.25 inches compared to the typical 4.5 x 2.75 inches, making it visually more prominent. Furthermore, the snap-on design of the wall plate makes alignment challenging. Once snapped into place, it is difficult to remove without bending or potentially breaking, complicating any necessary adjustments for a straight and level installation. The electrical design of the HS220 is a hybrid approach, utilizing both screw terminals for line and load wires and pigtails for neutral and ground connections. This design aims to conserve space within the junction box by reducing the number of wire nuts required for installation. Operating through the TP-Link Kasa app, the HS220 offers a straightforward setup process involving a temporary Wi-Fi access point connection. The Kasa app allows users to control power, adjust brightness, and set preset light levels. It also includes basic scheduling and timer functions, useful for vacation controls. The switch can be integrated with other Kasa Smart devices and supports popular smart home ecosystems such as Amazon Alexa, Google Assistant, Microsoft Cortana, and IFTTT, ensuring broad compatibility and smooth operation. Retailing around $45, the HS220 is competitively priced compared to other smart dimmers on the market. For instance, it is less expensive than the C by GE C-Start (which includes a motion sensor) and the Wemo Wi-Fi Smart Dimmer and Lutron Caséta Smart Lighting Dimmer Switch, both of which support Apple HomeKit (a feature lacking in the HS220). However, a significant limitation of the TP-Link HS220 is its inability to operate on multi-way circuits, as it is designed exclusively for single-pole installations. This restricts its applicability in homes with complex lighting configurations where multiple switches control a single light fixture. #SmartHome #SmartLighting #DimmerSwitch #WiFiConnectivity #KasaApp #HomeAutomation #SmartHomeReview

The Philips Hue Tento is an upcoming ceiling light model designed to offer a more affordable option within the Philips Hue ecosystem. This article provides an initial review based on personal impressions, focusing on its design, build quality, and installation features, ahead of its expected launch. Seven different models will be available in white and black finishes. European markets are anticipated to see the release of 42.1 cm and 54.2 cm diameter variants as early as next week. The smaller 29.1 cm version is slated for a mid-September launch, likely in the 38th calendar week. However, there is no confirmed launch date for countries outside the EU for this year. The pricing structure for the Hue Tento models is competitive, starting from 69.99€ for the 29.1 cm Hue Tento White, 89.99€ for the 29.1 cm White Ambiance model, and 109.99€ for the 29.1 cm White Ambiance and Colour version. Larger models with increased functionality are priced up to 199.99€. A key design aspect of the Philips Hue Tento is its remarkably flat profile. The smallest model measures only 2.5 centimeters thick, while the larger versions are 3 to 3.5 centimeters thick. This slim design contributes to compact packaging, which helps in cost savings. The construction primarily utilizes plastic, noted for its solid craftsmanship and absence of perceived weaknesses, a pragmatic choice given that ceiling lights are rarely handled post-installation. A notable improvement over previous premium Philips Hue models is the simplified wiring process. The Hue Tento eliminates the need for a screwdriver, as cables are easily plugged into terminals, making installation more user-friendly. In terms of lighting performance, the integrated LED strip provides consistent and even illumination. The brightness levels are robust, with the smallest model offering up to 2,250 lumens, the medium size up to 3,100 lumens, and the largest reaching up to 3,500 lumens. An aesthetically pleasing detail is the partially transparent top surface, which allows a subtle glow of light to extend towards the ceiling, adding an ambient accent to the room. Overall, the initial impressions of the Philips Hue Tento are highly positive, highlighting its value proposition through competitive pricing, sleek design, and improved installation convenience. #PhilipsHue #HueTento #SmartLighting #CeilingLight #HomeAutomation #LEDLighting #SmartHome #ProductReview